Are you currently searching for information about HVAC Service Companies?

Check our our Video

HOW TO LOCATE YOUR FURNACE

Air circulation in your home

If you have central heating, the furnace (also known as an air handler) in your home will heat your air in the winter while the blower motor circulates the air throughout your home. The AC evaporator coils for your air handler remove heat and humidity in summer. After your furnace heats or cools your air, it is then supplied to the duct system and the air begins flowing through your registers.

How many air systems run in your home?

Your thermostat is what sets the temperature in your home for your comfort. The number of thermostat(s) determine how many systems work to regulate your indoor air for heating and cooling.

Improve IAQ with Duct cleaning

Air duct cleaning can help reduce allergies from dust and other pollutants. Pollen, dust, and mold spores can get trapped in your duct work, which means that it's being continuously circulated throughout the air you breathe at home.

According to the U.S. Department of Energy (DOE), 25 to 40 percent of the energy used for heating or cooling a home is wasted. Contaminants in the heating and cooling system cause it to work harder and shorten the life of your system. Although filters are used, the heating and cooling system still gets dirty through normal use.

The National Air Duct Cleaners Association (NADCA) recommends air duct cleaning for improvement of Indoor Air Quality (IAQ). A certified duct cleaning will include cleaning of the furnace, the main trunk line [for air circulation] and all vents (including supplies and returns) each cleaned out individually.

Where is a furnace/air-handler typically located in a home?

Typically your furnace is centrally located in the home. It is usually located in an area such as a utility closet (by a cold air return), garage, attic, basement, or crawlspace; in the case of a heat-pump (a dual-system) it will be located outside of the home. When your system is run with a heat pump, it is likely a typical duct cleaning will include cleaning of evaporator coils with full system cleanings. Your furnace is usually located by other mechanical equipment such as the hot water heater, a [permanently installed] central vacuum cleaner, or a water softener, if this equipment is installed in your home.

AC Repairs https://www.advantaclean.com/blog/2014/november/how-to-locate-your-furnace/

How One Can Avoid High Heating Repair Bills

You can maintain an furnace system a number of different ways. Odds are, during winter months your heater runs all day trying to keep the home warm. Actually, it is probably on more than it needs to be because it is incapable of maintaining an operable environment. When trouble shooting and improving the heating portion of your furnace system, there are several things to consider.

Replace The Air Filter

This is the part you usually hear people talking about most often, but so few people take the advice and check it. If there is a obstruction, you either run the chance of not distributing heat effectively or possibly starting a fire.When the air filter becomes dirty air cannot flow through either which means the unit must work harder and could also mean a risk of fire. When the furnace works overtime, it is more expensive to operate. The fire concern is obviously self-explanatory. Neither scenario is good for your wallet or your well-being..

Assess The Blower

Check your blower blades and clean them up. A dirty fan will work harder to blow the air around and of course use more energy to maintain the thermostat level you choose it at. This means strain on your furnace system and your pocketbook since more energy is needed to constantly run the blower.

Check To See That The Fire Damper Works

Be certain to check your fire damper for correct operation. The fire damper is self-explanatory so take note of this component.

The Flex Duct

It is possible that your ducts became impaired throughout the years for different reasons. If there are obstructions or the duct has flattened anywhere the furnace system will think the correct warmth has been achieved, which will be wrong. Finally your equipment will be straining to keep your house cool while you keep on adjusting the thermostat to reach cozy settings.

Band Insulation

It is easy to overlook the insulation, but is one of the most common reason for a system malfunctioning. Take take time to focus on the insulation in between the duct work and the outside to make sure it has not worked itself loose. If this has happened, your system will not reach optimal temperatures and will work overtime to attempt to accommodate.

Ductwork Needs To Be Connected

Make be certain the ductwork is hooked up everywhere to all sections. Disconnected ductwork will allow warm air to escape and of course increase the running costs.

Check For Leaks In The Return Air Inlets And The Zone Dampers

Be sure to check that return air intakes are dirt free and in working order or your system will be unbalanced. Check your dampers verifying that they are in the best position. Every so often a damper can get moved in error like when you fit by it, or make room for storage. For a properly working system, look to see that the dampers are actually in the best spot.

If these everyday jobs are more than what you are confident with, it would be wise to hire an area heating service licensed for furnace and gas furnaces. There will be numerous heating contractors close to you who will care for all of this quite capably. The most sage advice we can offer is to set up yearly upkeep for this appliance.

Do you like more info about Local HVAC Repair? Give a review directly below. We will be pleased to hear your reactions about this review. We are looking forward to see you back again before long. In case you liked our post kindly remember to share it. Thanks for your time spent reading it.